Cheshire County Seal


Cheshire County Registry of Deeds

33 West Street
Keene, New Hampshire 03431

Tel. (603)352-0403 Fax (603)352-7678
Office hours - Monday through Friday 8:00 am - 4:00 pm
Closed State Holidays

 
      Cheshire Home
 
 
 
Plat Law


PURSUANT TO PARAGRAPH II OF THE PLAT LAW, Cheshire prefers to have the upper left hand corner reserved for the recording data.

RSA 478:1-a Recording of Plats.

I.  No register of deeds shall file or record a plat of a subdivision, or a plat prepared for the purpose of showing existing property lines, if such plat has not been prepared and certified by a licensed land surveyor, since July 1, 1981, or by a registered land surveyor between January 1, 1970 and June 30, 1981, and any such filing or recording shall be void. For the purposes of this section the definition of the word “subdivision” shall be that contained in RSA 672:14. A “plat” for the purpose of this section shall be a map of a specific land area whose boundaries are defined by metes and bounds. A plat may show:

(a)  Newly created parcels, streets, alleys, and easements as in a subdivision; or
(b)  A lot-line-adjustment or site plan depicting existing parcels defined by legal descriptions contained in deeds, grants, or other legal documents

II.  Each register of deeds shall establish a policy for providing adequate space, on the plat, for recording the registry plan number and recording information.

III.  The register of deeds shall refuse for recording any map that does not meet the definition of a plat under paragraph I and any plat that does not contain the information or meet the specifications required by this section. Construction plans, constructions details and maps that do not define the limits or extent of legal rights or interest in land shall not be recorded.

IV.  All plats shall be drawn with the following sizes: 8.5”x11”, 11”x17”, 17”x22”, 22”x34”, or such specifications and sizes as may be required by the register of deeds. The material composition of the plats shall be suitable for electronic scanning and archiving by the register of deeds.

V.  All plats shall have a minimum of ½ inch margins on all sides.

VI.  All text and dimensions shall be legible for reproduction, and the text sizes shall be no smaller than .08 of an inch for mechanical drafting and 1/8 inch for hand drafting.

VII.  All certifications, seals, and approval blocks shall have original dates and signatures in a legible, permanent black ink.

VIII.  All title blocks shall be located in the lower right hand corner, when possible, and shall indicate the following:

(a)  Type of survey, such as a boundary survey, subdivision, American Land Title Association (ALTA) survey, or lot line adjustment.
(b)  Owner of record.
(c)  Title of plat or development.
(d)  Tax map number.
(e)  Name of the town in which the parcel is located
(f)  Plat and revision dates.

IX.  All plats shall have a scale both as a written and graphic representation.

X.  All plats shall have a north arrow with reference to magnetic grid or astronomic north, as applicable. The north arrow shall be labeled with its reference direction.

XI.  Shading over any text shall not be permitted on any plat. Cross hatching or other hatching at a scale large enough not to interfere with text legibility, before and after reproduction, may be permitted.

XII.  No lines, whether hatching, boundary lines, or topographic contours shall obstruct or interfere with the legibility, either before or after reproduction, of any bearings, dimensions, or text.

XIII.  The minimum line widths on plats shall not be smaller than .01 inches.

Effective Date: January 1, 2005



 

Anna Z. Tilton, Register
atilton@nhdeeds.com
www.co.cheshire.nh.us/Deeds

Mira Cook, Deputy
mcook@nhdeeds.com

Copy Dept.
Tel (603) 355-3001
Fax (603) 355-4859
cheshirecopies@nhdeeds.com

Cheshire Registry
Tel. (603)352-0403

 

Website Technical Support
Fidlar Technologies
1-800-286-2478 or 563-345-1290
support@nhdeeds.com

REMOTE SUPPORT